 
Coupled Power Inductors
|
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
 |
||||||||||
| LPD5010-681ME_ | 0.68 ±20% | 0.07 | 191 | 0.95 | 0.07 | 2.6 | 2.7 | 2.8 | 1.95 | 2.76 |
| LPD5010-102ME_ | 1.0 ±20% | 0.10 | 150 | 0.95 | 0.09 | 2.1 | 2.1 | 2.2 | 1.50 | 2.12 |
| LPD5010-152ME_ | 1.5 ±20% | 0.15 | 134 | 0.97 | 0.10 | 1.7 | 1.8 | 1.8 | 1.20 | 1.70 |
| LPD5010-222ME_ | 2.2 ±20% | 0.20 | 108 | 0.97 | 0.11 | 1.5 | 1.6 | 1.6 | 1.10 | 1.56 |
| LPD5010-332ME_ | 3.3 ±20% | 0.27 | 83 | 0.98 | 0.13 | 1.2 | 1.3 | 1.3 | 0.95 | 1.34 |
| LPD5010-472ME_ | 4.7 ±20% | 0.40 | 68 | 0.98 | 0.15 | 0.98 | 1.0 | 1.1 | 0.75 | 1.06 |
| LPD5010-562ME_ | 5.6 ±20% | 0.45 | 60 | 0.99 | 0.16 | 0.90 | 0.93 | 0.94 | 0.70 | 0.99 |
| LPD5010-682ME_ | 6.8 ±20% | 0.53 | 55 | 0.99 | 0.19 | 0.83 | 0.86 | 0.87 | 0.60 | 0.85 |
| LPD5010-822ME_ | 8.2 ±20% | 0.70 | 50 | 0.99 | 0.22 | 0.74 | 0.77 | 0.78 | 0.50 | 0.71 |
| LPD5010-103ME_ | 10 ±20% | 0.78 | 46 | 0.99 | 0.27 | 0.67 | 0.69 | 0.70 | 0.50 | 0.71 |
| LPD5010-153ME_ | 15 ±20% | 1.19 | 33 | 0.99 | 0.34 | 0.53 | 0.55 | 0.56 | 0.42 | 0.59 |
| LPD5010-223ME_ | 22 ±20% | 1.58 | 26 | 0.99 | 0.40 | 0.45 | 0.47 | 0.48 | 0.35 | 0.49 |
| LPD5010-333ME_ | 33 ±20% | 2.50 | 23 | 0.99 | 0.48 | 0.37 | 0.38 | 0.39 | 0.30 | 0.42 |
| LPD5010-473ME_ | 47 ±20% | 3.48 | 17.0 | 0.99 | 0.63 | 0.31 | 0.32 | 0.33 | 0.25 | 0.35 |
| LPD5010-683ME_ | 68 ±20% | 5.10 | 14.9 | 0.99 | 0.90 | 0.25 | 0.26 | 0.27 | 0.19 | 0.26 |
| LPD5010-104ME_ | 100 ±20% | 8.0 | 11.2 | 0.99 | 1.39 | 0.21 | 0.22 | 0.22 | 0.15 | 0.21 |
| LPD5010-154ME_ | 150 ±20% | 11.7 | 9.9 | 0.99 | 2.10 | 0.17 | 0.17 | 0.18 | 0.12 | 0.16 |
| LPD5010-224ME_ | 220 ±20% | 15.2 | 8.05 | 0.99 | 3.02 | 0.14 | 0.15 | 0.15 | 0.11 | 0.15 |
 |
|
|
|
|
|
|
|
|
|
|
| 1 | When ordering, please specify termination and packaging codes: e.g. LPD5010-224MEC | |
| Termination: | E = Silver-palladium-platinum-glass frit Special order, added cost: T = RoHS tin-silver-copper (95.5/4/0.5) or S = non-RoHS tin-lead (63/37). |
|
| Packaging:
|
C = 7"
machine-ready reel EIA-481 embossed plastic tape 1000 parts per full reel). B = Less than full reel In tape, but not machine-ready. To have a leader and trailer added ($25 charge), use code letter C instead. D = 13" machine-ready reel EIA-481 embossed plastic tape. Factory order only, not stocked (3500 parts per full reel). |
|
| 2 | Inductance shown for each winding, measured at 100 kHz, 0.1 Vrms, 0 Adc on an Agilent/HP 4284A LCR meter or equivalent. When leads are connected in parallel, inductance is the same value. When leads are connected in series, inductance is four times the value | |
| 3 | DCR is for each winding. When leads are connected in parallel, DCR is half the value. When leads are connected in series, DCR is twice the value. | |
| 4 | SRF measured using an Agilent/HP 4191A or equivalent. When leads are connected in parallel, SRF is the same value. | |
| 5 | ||
| 6 | Isat: DC current, at which the inductance drops the specified amount from its value without current. It is the sum of the current flowing in both windings. | |
| 7 | Irms, both windings: Equal current when applied to each winding simultaneously that causes a 40°C temperature rise from 25°C ambient. See temperature rise calculation. | |
| 8 | Irms, one winding: Maximum current when applied to one winding that causes a 40°C temperature rise from 25°C ambient. See temperature rise calculation. | |
| 9 | Ambient temperature range: |
–40°C to +85°C with Irms current. +85°C to +125°C with derated current. Derating curve |
| 10 | Storage temperature range: | Component: –40°C to +125°C T&R packaging: –40°C to +80°C |
| 11 | Resistance to soldering heat: Three reflows at >217°C for 90 seconds (+260°C ±5°C for 20 – 40 seconds), allowing parts to cool to room temperature between. | |
| 12 | Electrical specifications at 25°C. | |
| Refer to Soldering Coilcraft Components before soldering. | ||
|
|
||